Battery pack / fuel cell / e-Powertrain
DC source/sink
Multi-Channel System
MI-TS-3871: Multi-channel system for energy-saving tests and simulations. Multi-channel system for energy-saving tests and simulations. Two or four outputs, up to 1500 V
and 1200 A per output (without galvanic isolation between the DC outputs // Maximum values for voltage, current and number of output channels depending on the specifi c confi guration).
Our high-performance test system MI-TS (Multichannel Infeed test system) is a multi-channel, highly dynamic, bidirectional DC power supply with continuous and seamless transition from source to sink
mode. Thanks to its multi-channel capability and outstanding performance, the MI-TS is the ideal test system for a wide range of applications in the automotive, hydrogen and laboratory sectors. At the same time, it off ers the possibility of increasing performance thanks to parallel output channels.
Standard features
- The MI-TS-3871 impresses even in the standard system configuration with its extensive equipment and is therefore ready for immediate use by customers from all over the world. The following is a small excerpt:
General information - Input voltage 380 / 400 V, 50 / 60 Hz
- Sense connections for voltage measurement / regulation
- DC current and voltage measurement with 0.1 % full scale accuracy
- Battery tester version
- Protection class IP20
- Noise-reduced design (vibration metals, fan control)
- Air cooling
- Parallel operation of the output channels to increase the current
Safety features
- Lockable main switch as load-break switch
- Safety control for Performance Level d in accordance with EN 60204-1 / ISO 13849-1
- Stop switch in cabinet door
- Voltmeter and indicator light in cabinet door
- Redundant DC output contactors
- Connection terminals for external „emergency stop“
- Connection terminals for external „stop“
- DC output electrically isolated from the AC mains (galvanic isolation)
Interfaces
- 10 inch display with touch operation
- Modbus / TCP interface
- CAN interface
- VNC interface
Options (extract)
- Security level
Increase to performance level e as a special option - Battery emulation version (increased output capacity)
Hardware and software adaptation for special applications
to improve voltage stability for battery emulation - Protective diode at the DC output
Switchable diode to protect the device under test in sink-only mode - Insulation monitoring
Protective device for monitoring the galvanic isolation of the DC output
- Interfaces
Large selection of various optional interfaces such as CAN high-speed (1 kHz), SCPI, EtherCAT, Profi bus, Profi net, analog, LabVIEW, Matlab/Simulink - DC output contactors with higher performance
DC output contactors with increased current capability are optionally available to increase the service life - Door contact switch, door locking device, special locking cylinder
Operator safety is our top priority, therefore additional safety equipment is available for our customers
- System cabinets in a special design
Rittal enclosures, special bases, enclosures on castors, special paint fi nishes, wire end marking. The I-TS can be adapted to a wide range of customer requirements and local conditions - Due to grid operarotor regulations, NA protection may be
required to monitor the grid quality for the MI-TSNA protection with grid analysis measuring device for power generation systems (VDE-AR-N 4105, VDE-AR-N 4110)
Aufgrund von Richtlinien des Netzbetreibers kann ein NA-Schutz zur Überwachung der Netzqualität für das MI-TS erforderlich sein - Water cooling including increased protection class IP54
Water cooling of the system cabinets is available to minimize waste heat to the room or to reduce noise. This also increases the protection class of the MI-TS
Typical applications
- Battery tests (charge and discharge tests of batteries)
- Battery simulation / battery emulation
- Load for fuel cells
- Test power supply for contactors, fuses and circuit breakers
- Test of DC motors (drive train)
- Testing of charging columns (comemso)
- Power supply to trains for maintenance purposes at the ICE (German high speed train) plants
Technical data
Type MI-TS-3871
AC mains voltage / | 380 / 400 / 440 / 480 / 690 V ± 10 %, |
Measurement accuracy | Voltage: 16 Bit ADC // Current: 16 Bit ADC |
Control accuracy | Voltage: 0,1 % fs // Current: 0,1 % fs |
Residual ripple | Voltage: ≤ 0.1 % eff. fs |
Voltage tolerance | Battery tester< 3% fs |
Short circuit performance | Short circuit proof: |
Permissible environmental conditions: | 1K21 / 1M11, +5 bis +40 °C |
Cooling method | Cooling method Enforced air cooling (IP20, IP21, IP23) // enforced water cooling (IP54) |
Safety of machinery - | EN ISO 13849-1 |
Safety of machinery | EN 60204-1 Exception: |
EMC Standards | EN 61000-2-4 Class 3 |
Available types
Type | I-TS-3871-300 | I-TS-3871-600 | I-TS-3871-800 | I-TS-3871-1000 | I-TS-3871-1200 | I-TS-3871-1500 |
|---|---|---|---|---|---|---|
max. DC voltage in V | 300 | 600 | 800 | 1000 | 1200 | 1500 |
Power in kW | 60, 120, 160 | 60, 100, 160, 250, 320, 400, 500 | 100, 160, 250, 320, 400, 500 | 60, 100, 160, 250, 320, 400, 500, 650 | 320, 650 | 400 |
Current in A |
|
|
|
|
|
|
Current rise time at 0.5x UNenn 10 % - 90 % in ms | < 1,0 | < 1,0 | < 1,0 | < 1,3 | < 1,0 | < 1,4 |
Subject to technical changes
We will be happy to check your requirements/
Brochure as PDF
Brochure 1200 V, 1200 A as PDF
Learn more!
You want to know more about our products? We will be happy to send you more information by e-mail!
